LS-671~VRC

Overview

This is a simple speaker that is used with the SINCGARS series radios. This speaker can be adapted for use with other systems. This is an amplified speaker and will need 12 or 24 volts to function properly.

• 
• 

Usage

(CB1) Power ON/OFF Switch

On Off switch for the powered speaker and accessories connected via pin D

(J1) Cable Connector

interface cable connection

(J2) Handset Connector

H250 Style handset Microphone connects here

(DS1) Power Indicator Lamp

Lamp indicates power is on in the speaker. This can be dimmed by turning the outer housing. The housing can also unscreww to replace the lamp. Uses the common bulb seen on VIC1-Vic4 and many Radios VRC Series and later

(R1) Volume Control

This controls the volume for both the Handset connected to J2 and the speaker itself.

Pushing the knob in, shuts off the external speaker and also provides volume control to the handset mic.

Pulling out the knob, enables the external speaker and controls its volume.

Schematics

General Schematic and block Diagram

Schematic of the interhook cable

Pinouts

Pin	Description	Notes
A	Ground	This is used for both the audio ground and a power ground
B	Unswitched 24v	(B + Line) This is used as a constant 24v source into the speaker, to use the speaker this is required as a minumum
C	Switched 24V in	(Relay control line) This allows 24v to be supplied to PIN D when the power switch is turned on
D	Switched 24V out	(Power Relay Control Line) PIN C is is connection to this pin, when the power switch is turned on
E	Test Point speaker -	This is used to test the speaker, bypassing the audio circuits
F	Test Point. speaker +	This is used to test the speaker, bypassing the audio circuits
J	Remote PTT	When the PTT key on the Microphone connected to J1 is pressed, this pin connects to Ground PIN A.
K	RX Audio in	receive audio source is hooked here, this should be isolated with a transformer if a 12volt radio is used
S	Routed to PIN A	This is usually the PTT line in VIC1 configurations, since this is routed the Ground, hooking this to a VIC1 using the wrong cable will cause the speaker to key the radio.
U	Transmit Audio

Hooking up as a simple speaker

Properly interfacing this speaker into 12volt radio, will require the use of an isolation circuit to prevent the 24volt system from harming the 12volt radios. example interfaces can be seen in integrating with other equipment

Generally speaking you can hook the "audio GND" line to the "ring" of an audio jack and the "Audio in" to the "tip"

24 Volt Vehicle / 12 Volt Radio (amplified)

The use of the transformer is to isolate the 24volt speaker from the 12volt audio source. Without this you run the risk of exposing the 12volt radio to 24volt source... not a good idea..

Known Limitations

None Found

12 Volt Vehicle / 12 volt Radio (amplified)

If you choose to use 12Volt for the power to the speaker the transformer is not required.

Known Limitations

These are differences in operation we noticed when using this with 12volts, these are confirmed to work fine if you use 24 volts.

The light bulb will be dim,

The voltage is 1/2 of the rating of the bulb, it will be dim.

If you want to replace it, the part number is: 12 Volt: GE 394 (replaces the stock 24 Volt bulb: OL-387 or GE 387)

Pushing the volume control down doesn't mute the radio speaker

(not sure why yet)

Hooking up as a simple speaker (un-amplified)

you can also hook this speaker up in a way that bypasses all the circuits. These points are used to test the speaker. This will likely sound "tinny" but it will work.

Known Limitations

None of the controls function

This is because we bypassed everything and went directly to the speaker

Hooking up for full PTT, transmit and receive audio for non-military radios

This method will allow you to have full Transmit (TX) and Receive (RX) from any 12volt radio.

NOTE: do not hookup the ground to PIN S or feedback on the transmit audio will occur.

THIS IS A WORK IN PROGRESS!

Known Limitations

These are differences in operation we noticed when using this with 12volts, these are confirmed to work fine if you use 24 volts.

The light bulb will be dim,

The voltage is 1/2 of the rating of the bulb, it will be dim.

If you want to replace it, the part number is: 12 Volt: GE 394 (replaces the stock 24 Volt bulb: OL-387 or GE 387)

Pushing the volume control down doesn't mute the radio speaker

(not sure why yet)

Low TX output audio

This is due to the reduced voltage, working on a solution

In my system i was getting a notable buzz on the transmit audio, this is was due to some bad connections . Upon testing the signal report was clear, but audio was low. I expected that though, i need to adjust this internally by some mods. Still Experimenting...

Using the LS-671 to remotely Power On/Off any 12volt radio

The LS-671 has some interesting features that allow it to remotely turn on/off radios. for example, mounting a CB, GMRS, AM/FM under the seat and using the LS-671 Power switch to turn on and off the other radio. Of course you would have remote volume control receive audio and transmit functions...

Below is a schematic of the hookup to allow this speaker to control a radio.. it offers:

Remote On/Off of the radio by the from power switch on the speaker

Volume control for RX

Transmit for TX

This uses a simple 12volt relay to connect the 12volt power line of the radio, this is accomplished by Pin D of the Ls-671 where voltage is applied when the speaker is turned on. You need to use a relay because its unlikely the speaker will be able to handle the power draw of the radio (especially in transmit). You can use any 12volt relay, the one listed is a SPDT but i also used a DPDT from radio shack (OMI-SS-212D)

I Think that is all this speaker can do, anything else?

\:-) happy hacking