Difference between revisions of "AN~PRC-74"
RadioNerds (talk | contribs) (→Images) |
RadioNerds (talk | contribs) (→Images) |
||
Line 49: | Line 49: | ||
File:AN-PRC-74-37.png | File:AN-PRC-74-37.png | ||
File:AN-PRC-74-38.png | File:AN-PRC-74-38.png | ||
+ | File:AN-PRC-74-39.png | ||
</gallery> | </gallery> | ||
+ | |||
;These Images are from a complete wiring harness swap. The front audio section of a PRC-74 was hacked to pieces in a botched HAM conversion. I replaced the entire wiring harness of the radio with a donor PRC-74B after confirming every connection in the harnesses were the same. | ;These Images are from a complete wiring harness swap. The front audio section of a PRC-74 was hacked to pieces in a botched HAM conversion. I replaced the entire wiring harness of the radio with a donor PRC-74B after confirming every connection in the harnesses were the same. |
Revision as of 02:04, 11 September 2013
Contents
Overview
Radio Set AN/PRC-74 or the AN/PRC-74A is a lightweight, two-way communications set that is capable of receiving and transmitting voice and telegraph signals. Single-sideband (SSB) modulation is used for voice transmission, and continuous wave (CW) modulation is used for telegraph transmissions. The voice and telegraph receptions are demodulated and applied to a headset. The frequency range of the radio set for both receive and transmit modes of operation is between 2.0 mHz and 11.999 mHz for the A models and 2.0 - 17.999 mHz for the "B" version.
The radio set may be portably operated or operated at a fixed station. When portably operated, the radio set is powered by either a rechargeable nickel cadmium storage battery pack, or a dry cell battery pack. An external battery charger and power supply assemblies are provided with the radio set when used at a fixed station. The power supply assembly allows the radio set to be powered by either the alternating current (AC) or direct current (DC) voltages available at the operating site. The external battery charger assembly is used to recharge the radio set batteries prior to using the radio set portably.
Three types of antennas are supplied with the radio set. Operating in the low end of the high frequency spectrum, the range of the radio set may be extended to hundreds of miles with the proper selection of frequency and antenna type.
The operational features of the AN/PRC- 74 and AN/PRC-74A are identical except that the A model has been modified by MWO 11- 5820-590-35/1 to permit operation with the AN/GRA-71 coder burst equipment. Refer to TM 11-5820-590-12 for operational procedures for coder burst operation. Refer to paragraph 1-59 of the technical manual for circuit differences between the two models.
Specifications
- Frequency range
- 2.000 to 17.999 mc in 1.0 kc steps.
- Frequency standard stability
- ± 1.5 parts/million from -30°C to +55°C (AN(PRC-74B).± 1.5 parts/million from -40°C to +65°C (AN/PRC-74C).
- Intermediate frequency
- 1,750 kc.
Transmitter performance:
- Modulation modes
- Upper-sideband suppressed carrier, voice or cw.
- Carrier suppression
- 40 db below level of a 1,000- cycle modulation usb signal of rated output.
- Power output
- 15 watts peak envelope power nominal.
- Monitor sidetone
- Voice or tone as determined by modulation mode.
- Tuning indicator
- Meter (operated by vswr bridge).
Receiver performance:
- Sensitivity
- 0.7 microvolt for 10 db, signal plus noise to noise.
- Selectivity
- .3-db points at +300 and + 2,700 cps, 45-db points at -350 and + 6,500 cps (referenced to carrier frequency).
- Audio output
- 1 mw minimum into a 500-ohm headset.
- Audio distortion
- 10 percent maximum at frequencies between 300 cps and 2,700 cps with an audio output level of 4 milliwatts.
- Power source
- Determined by fixed or portable requirements: An external power supply may be used as a power source during fixed operation. For portable use, wet or dry battery pack may be used.
- Input power
- + 10.5 to + 17.0 volts
Images
- These Images are from a complete wiring harness swap. The front audio section of a PRC-74 was hacked to pieces in a botched HAM conversion. I replaced the entire wiring harness of the radio with a donor PRC-74B after confirming every connection in the harnesses were the same.
- I replaced the harness from left to right, only removing parts as i was ready to connect the new harness.
Antenna
Included Dipole Examples
Required Wire Lengths
Dipole Wire Leg Lengths | |||||
---|---|---|---|---|---|
Freq (MHz) | Length (Ft.) | Freq (MHz) | Length (Ft.) | Freq (MHz) | Length (Ft.) |
2.00 | 117 | 5.0 | 47 | 13.00 | 18 |
2.20 | 106 | 5.50 | 43 | 14.00 | 17 |
2.40 | 98 | 6.00 | 39 | 15.00 | 16 |
2.60 | 90 | 6.50 | 36 | 16.00 | 15 |
2.80 | 84 | 7.00 | 33 | 17.00 | 14 |
3.00 | 78 | 7.50 | 31 | 18.00 | 13 |
3.25 | 72 | 8.00 | 29 | MEASURE WIRE LENGTH ACCURATELY FOR OPERATING FREQUENCY
USING THE WRONG LENGTH MAY DAMAGE THE RADIO SET. | |
3.50 | 67 | 8.50 | 28 | ||
3.75 | 62 | 9.00 | 26 | ||
4.00 | 58 | 9.50 | 25 | ||
4.25 | 55 | 10.00 | 23 | ||
4.50 | 52 | 11.00 | 21 | ||
4.75 | 49 | 12.00 | 20 |

Reference Files
PRC-74A
- DS, GS, AND DEPOT MAINTENANCE MANUAL
- RADIO SET
- AN/PRC-74
- JULY 1966
PRC-74B AND C
- OPERATOR'S AND ORGANIZATIONAL MAINTENANCE MANUAL (INCLUDING REPAIR PARTS AND SPECIAL TOOLS LISTS)
- RADIO SETS AN/PRC-74B (NSN 5820-00-935-0030)
- AN/PRC-74C (NSN 5820-00-177-1641);
- POWER SUPPLIES PP-4514/PRC-74 (NSN 5820-00-942-0821)
- PP-4514A/PRC-74 (NSN 5820-00-177-4581)
- BATTERY BOXES CY-6121/PRC-74 (NSN 5820-00-908-3127)
- CY-6314/PRC-74 AND CY-6314A/PRC-74 (NSN 5820-00-156-3934)
- March 1967
- DIRECT SUPPORT, GENERAL SUPPORT, AND DEPOT MAINTENANCE MANUAL
- INCLUDING REPAIR PARTS AND SPECIAL TOOLS LISTS)
- RADIO SETS AN/PRC-74B (NSN 5820-00-935-0030)
- AN/PRC-74C (NSN 5820-00-177-1641);
- POWER SUPPLIES PP-4514/PRC-74 (NSN 5820-00-942-0821)
- PP-4514A/PRC-74 (NSN 5820-00-177-4581)
- BATTERY BOXES CY-6121/PRC-74 (NSN 5820-00-908-3127)
- CY-6314/PRC-74 AND CY-6314A/PRC-74 (NSN 5820-00-156-3934)
- JULY 1968
- These are the missing schematics from the commonly found PRC-74B manual found on Google books
PRC-74 Instructions for adding Lower Sideband Support
- Defines the process required to add Lower SSB (LSB) support for the PRC-74
- James P Karlow