Difference between revisions of "TL - Tools"

Revision as of 19:29, 12 August 2023

Tools (Note (NIC) = not in 1920 catalogue)

TL-1 screwdriver, 3 1/2-inch
TL-2 screwdriver 4-inch
TL-3 (NIC) Stone, Carborundum, medium India, No. 53
TL-4 screwdriver 5-inch
TL-5 file
TL-6 wrench, double open end, 3-inch, 0.193-inch, 0.385-inch
TL-7 gauge
TL-8, wrench 4-inch
TL-9 file, 4-inch warding
TL-10 File (6Q37110) flat bastard, 6-inch
TL-11 ?
TL-12, plyers, round nose, side cutting, 6-inch
TL-13 ? (not in 1920 cat.) small lineman's pliers
TL-14 handle, file
TL-15 ?
TL-16 ?
TL-17 wrench 9-inch
TL-18 puller
TL-19 pliers, combination 6-inch
TL-20 pliers, combination 8-inch
TL-21 screwdriver 6 1/2-inch
TL-22 (NIC) Screwdriver, 4-inch flat tip, 6R15120.
TL-23 (NIC) screwdriver, 7-inch
TL-24 pliers, side cutting, 4-inch
TL-25 screwdriver, jewelers
TL-26 tape, 1/4-inch, cotton, for cable splicing. 1.000 yards
TL-27 screwdriver
TL-28 screwdriver
TL-29 knife
TL-30 file like TL-5 but with bent handle
TL-31, square, combination bevel and level
TL-32, calipers, outside,
TL-33
TL-34
TL-35, speed indicator
TL-36
TL-37
TL-38, hammer, ball peen, 12-Oz.
TL-39, (NIC) hammer, claw, 1-Lb.
TL-40, screw driver, 8 1/2-inch
TL-41
TL-42
TL-43
TL-44, Screwdriver 13 1/2-inchP/O TE-36
TL-45, soldering iron, 1.5 Lb.
TL-46 (NIC) soldering iron jewlers
TL-47, chisels, cold 1/2-inch
TL-48, chisels, cold 3/4-inch
TL-49, center punch, 4-inch
TL-50
TL-51, wrench, 6-inch
TL-52, wrench, 8-inch
TL-53
TL-54, wrench, monkey 6-inch
TL-55, wrench, stillson, 14-inch
TL-56
TL-57
TL-58
TL-59,tap and die set
TL-60, pliers diagonal, 6-inch
TL-61
TL-62, pliers, diagonal, 3 1/2-inch
TL-63, Bits, expansion, 7/8 to 3-inch,
TL-64, tinners snips
TL-65
TL-66 (NIC) torch
TL-67, hand drill 3/8-inch
TL-68, tool roll 10 assorted files
TL-69, tool roll, open end wrench's
TL-70, tool roll, assorted drills and reamers
TL-71, test clips
TL-72 (NIC) brush camels-hair, flat
TL-73, Lathes, metal working, 30-inch bed.
TL-74
TL-75
TL-76
TL-77
TL-78
TL-79
TL-80
TL-81, drift pin,
TL-82, wrench, alligator 10-inch
TL-83 tape 3/4-inch friction
TL-84 wrench, spanner, for BC-47 nuts
TL-85 wrench, double end,
TL-86 ?
TL-87 pliers, pointed nose, 4 3/8-inch
TL-88 wrench, double end,
TL-89 ?
TL-90 cable dresser
TL-91 ?
TL-92 socket wrench
TL-93 (NIC) rubber tape
TL-94 tape, rubber
TL-95 flashlight, fiber case, BA-1, 8 1/4" x 1 1/2 "
TL-96 tap and die set
TL-97 ? bandage ? P/O TE-56
TL-98 drift pin
TL-99 drift pin

( NOTE 1920 signal corps catalogue ends here )

TL-100, wrench RE-12
TL-101
TL-102 pliers,
TL-103 pliers, diagonal cutting 5-inch TE-6, TE-36
TL-104 saw, hand 26-inch
TL-105 screwdriver
TL-106 screwdriver
TL-107 pliers, side cutting, 8-inch
TL-108 nut driver, 6-inch, 3/8-inch head
TL-109 tape, cotton, 1-inch.
TL-110 spring loaded alligator clip
TL-111 6 inch adjustable wrench, Crescent #A-16
TL-112 10 inch adjustable wrench, Crescent #A-110
TL-113
TL-114
TL-115
TL-116 Electrician's Knife, (prototypes only)
TL-117 electric soldering iron
TL-118
TL-119 pliers, side cutting, 5-inch, P/O TE-5
TL-120 electric soldering iron
TL-121 electric soldering iron
TL-122 flashlight
TL-123
TL-124 bandage, cable splicing
TL-125 pliers, gas, combination screwdriver handle, TE-15, TE-44
TL-126 pliers, long chain nosed, 6-inch,
TL-127 gage TL-127 is provided with the generator in order to measure the regulator clearances TM 11-231
TL-128 screwdriver set
TL-129 saw, cross-cut,
TL-130 torch
TL-131 jewelers soldering iron
TL-132, Soldering iron P/O TE-36
TL-133 file 6-inch round
TL-134
TL-135 axe
TL-136
TL-137 clip electric, TS-27 test set
TL-138 Alignment tool
TL-139 soldering iron
TL-140
TL-141
TL-142
TL-143 sleeve rolling tool
TL-144 Gage, linemans climber
TL-145
TL-146
TL-147
TL-148
TL-149
TL-150 Alignment Tool
TL-151
TL-152
TL-153
TL-154
TL-155
TL-156
TL-157
TL-158
TL-159
TL-160
TL-161
TL-162, Block, and 25 Ft. 3/8th manilla rope.
TL-163
TL-164
TL-165
TL-166
TL-167
TL-168
TL-169
TL-170
TL-171
TL-172
TL-173
TL-174
TL-175
TL-176
TL-177
TL-178
TL-179
TL-180
TL-181
TL-182
TL-183
TL-184
TL-185
TL-186
TL-187
TL-188
TL-189
TL-190
TL-191
TL-192 tape 3/4-inch rubber
TL-193
TL-194
TL-195 punch and anvil set AN~MPM-1
TL-196 punch and anvil set AN~MPM-1
TL-197
TL-198
TL-199
TL-200
TL-201 tube puller
TL-202
TL-203
TL-204 Wrench, special tool, to adjust jack fastener on telephone switchboards, 18-inches long with wooden handles, and swivel head. PO. TE-44.
TL-205
TL-206
TL-207
TL-208
TL-209
TL-210
TL-211
TL-212
TL-213
TL-214 flashlight (beacon) for drop bag BG-121
TL-215 handle
TL-216 hammer
TL-217 sleeve compressing tool
TL-218
TL-219 miniature tube socket tool, P/O I-56 test set
TL-220 miniature tube pin die, P/O I-56 test set
TL-221
TL-222
TL-223
TL-224
TL-225
TL-226
TL-227
TL-228
TL-229
TL-230
TL-231
TL-232
TL-233
TL-234
TL-235
TL-236
TL-237
TL-238
TL-239
TL-240
TL-241
TL-242
TL-243
TL-244
TL-245
TL-246
TL-247
TL-248
TL-249
TL-250
TL-251
TL-252
TL-253
TL-254
TL-255
TL-256
TL-257
TL-258
TL-259
TL-260
TL-261
TL-262
TL-263
TL-264
TL-265
TL-266
TL-267
TL-268
TL-269
TL-270
TL-271
TL-272
TL-273
TL-274
TL-275
TL-276
TL-277
TL-278
TL-279
TL-280
TL-281
TL-282
TL-283
TL-284
TL-285
TL-286
TL-287
TL-288
TL-289
TL-290
TL-291
TL-292
TL-293
TL-294
TL-295
TL-296
TL-297
TL-298
TL-299
TL-300

(jumps to JETDS nomenclature)

TL-320/U petrol blow torch
TL-338/U vice
TL-547/U goggles
TL-608/U blowtorch

(jumps to JETDS nomenclature)

references

@@ Line 81: / Line 81: @@
 * [[TL-79]]
 * [[TL-80]]
-* [[TL-81]]
+* [[TL-81]], drift pin,
-* [[TL-82]] drift pin ?? wrench, alligator 10-inch ??
+* [[TL-82]], wrench, alligator 10-inch
 * [[TL-83]] tape 3/4-inch friction
 * [[TL-84]] wrench, spanner, for [[BC-47]] nuts

Difference between revisions of "TL - Tools"

Revision as of 19:29, 12 August 2023

references

Navigation menu

Personal tools

Namespaces

Variants

Views

More

Search

Navigation

General Info

Periodicals

Tools